Railtrack PNA

This is a rake of ten Bachmann PNA and other than my usual Spratt & Winkle fixed system  between wagons, they are completely standard. The rake includes each style of side reinforcements, five and seven bars.

This rake is an exercise in weathering using ‘Designers Gouache’, which is a water based paint that behaves like an oil based paint. The best thing about these paints are that they mix very well.  You can create depth and texture and if you don’t like your results you can wash it off with warm water. When you are happy with your results you make them permanent using enamel varnish. The only down side – they are a bit expensive for the best brands. I only use six colours!

As well as weathering the outside and underframe, I used this paint on the inside to look like wear and distress. I will eventually add some weathering powders to the inside of the wagons.  I have tried to vary the amount of weathering so that the rake looks realistic.

DSCF4167

DSCF4169

DSCF4170

 

DSCF4174

DSCF4176

 

DSCF4184

DSCF4187

DSCF4185

Advertisements

Seacow – Lima based

I detailed these wagons about 25 years ago, before the better Bachmann and Hornby models were available. There is no way I am going to criticise these wagons, as in those days, they were the best we could get and if you wanted something better, then you had to do it yourself.

I have put these on as a separate post because they are an exercise in a form of weathering called ‘dry brushing’. I used Humbrol enamel paints for this exercise. How to do this has appeared many times in magazines and I will not repeat it. In my opinion they still stand the test of time, and still look very much at home on my garage layout.

I did make some basic mistakes when I detailed  them, the main one was I used solid tops to the protectors instead of mesh – sorry. I also added some footsteps on the four corners. The hand brake wheels could also have been replaced with something more scale.

This a rake of five wagons.

 

DSCF4146

DSCF4147

DSCF4148

 

DSCF4152

 

WCR Mk2 Coaches

The middle of last year my wife and her friends went on a NENTA tour to Crich Tram museum. When I dropped her off at the station, I noticed that most of the stock was Air Conditioned Mk2’s.

I then decided I would like to build up a small rake, I thought five coaches topped and tailed would be nice. I purchased three, that’s all I could find at the local swap-meet and proceeded to strip them and paint them. This had to be another cheap project, this time I had to pay an average of £6 per coach for Mainline/Dapol  unboxed ones. Not as cheap as the DRS donor coaches!!!

Transfers this time were Railtec, and very good they are. Three down, two more to do.

Bachmann Collectors Club have just done a 37/7 – come on Bachmann how about a 47, or two!!!!!!!

DSCF4137

DSCF4139

DSCF4135

 

DRS Mk2 Coaches

This is a far more up to date rake of coaches. I went to Norwich to see the Class 37’s top & tail the Gt Yarmouth and Lowestoft trains, and although the stars are the 37’s, I thought it would be great to do the three coach rake.

I did not want to spend a lot on this project so I had a rummage at a local swap-meet and found three rather tatty Airfix/Mainline Mk2D coaches, 1 x BSO and 2 x TSO. I know these are technically not quite right, but they were £3 each – unboxed!

I already had a supply of DRS paint, so work started straight away. I sent for the appropriate transfers from R3sprays and they were soon finished.  Please note, I need to give them a slight weathering later. They look brilliant between two Bachmann 37/4’s.

DSCF4141

DSCF4142

DSCF4144

 

Scrap Train (1)

This is one of three scrap trains that I have made. This one is made up of five wagons, of three different types.

This rake dates from the late 80’s – early 90’s, and was typical of the days before privatisation.

The first types are three ready to run HSA’s by Bachmann. These have been filled with sundry cut-up bits of whitemetal and brass and then weathered. The HSA was a HEA with its hopper doors welded up, specifically for scrap.

The second type was a POA, this type were known as ‘Blackadders’, this is a scratch built body on a Hornby chassis. Again it was filled with ‘scrap’.

The third type of wagon was a bogie ‘Sheerness Steel’ wagon called a PXA. This was another of the excellent Appleby kits, the transfers were from the same source. Although I made this rake in the 90’s, I have obtained another PXA, part kit – no bogies, so the rake  could be added to when I obtain some bogies.

DSCF4124

DSCF4128

DSCF4132

DSCF4126

 

DSCF4133

 

Nuclear Flask with barriers & Brake Van

I guess this was the normal Flask train through the 70’s and 80’s. I saw this formation many times at Ipswich, to and from Sizewell.

The Brake van is a slightly modified Hornby, The two barriers wagons (RNA)  were made from Bachmann HEA’s with resin tops replacing the hopper. I believe the tops were to add weight to the wagons and were steel or concrete or a combination of both. I believe these tops were supplied to me from Appleby Models and are in resin.

The flask (FNA) itself was again I believe from Appleby and was in resin. I used Fox transfers for all wagons.

In these days, the train was hauled by a single loco – usually a Stratford 31 or 37.

DSCF4106

DSCF4107

DSCF4108

DSCF4109

Bitumen TTA Tanks

This is yet another rake of wagons based on the Hornby TTA. I have had two goes at these wagons. After originally making them in the late eighties, I further updated them about five years ago. Bitumen is a very thick product and before it can be unloaded it has to be heated so it becomes thinner. This is done in tubes that run through the wagon, there are also ‘chimneys’ on the top of the wagons to exhaust the fumes from the ‘Flamers’ which are on the opposite end to the ladder..

I first saw these wagons at my local station during the 70’s. The wagons were unloaded as described above and them pumped about 100 yards to  a ‘Tar Factory’ . This factory supplied tar in heated road tankers to local councils for road repairs/recoating, it was used with those lovely road chippings! If I remember rightly, the factory was operated by a company called ‘Printar’. Sadly the factory closed and the traffic ceased in the early eighties.

The wagons I built are about 90% correct and are a generic attempt, but again, something is better than nothing.  The wagon flamers and chimneys are made from Plastic Tubing and the hatches at the end of the wagons are, don’t laugh, drawing pins.

DSCF4114

DSCF4112

 

DSCF4119

DSCF4120

DSCF4121